Instructions on how to paint strip (paint stripping 101) – our other built in saga

Paint stripping isn’t the most fun task but here are some step by step instructions to make it a little easier! You need to be 100% committed but the results will be worth it in the end.

Supplies

Citristrip

Paint scraper

Sander or Manual with both 80 grit and 220 grit sand paper & steel wool (optional)

Lead paint test

Dust mask

Wood stain

Cheap paint brush

Gloves

Cloth (for rubbing in the stain & finish)

Trash bin with liner

Paper or something to cover the floor you will be stripping over

Mineral spirits to clean paint brushes if you will use a brush (optional)

Wood conditioner (optional)

Tung oil or finish (optional)

Wood filler (optional)

Patience

Pre-step

Know what you’re getting into! This will consume a lot of time, especially if the project is large. We did 2 projects at once because we wanted to finish the stripping before our new hardwoods got installed.

Image

Step 1

Get your supplies ready and prepare for the mess.

I personally liked the citristrip after I started originally with heavy duty paint stripper. The citristrip works just as well (if not better) but it is more expensive. However, after getting paint stripper accidentally on my skin and because I was doing this indoors, I went with citristrip. It smells like citrus and has a spongy texture and does not burn! It works in 30 min or less.

Image

Step 2

Check for lead paint. I wore a dust mask any way because I did some dry chipping. If you can dry chip- it saves time so try to do that first.

Image

Step 3

Put the paint stripper on until the paint bubbles and pulls away. Scrape away! Hint: the better quality scraper, the better experience you will have. We bought a $30 one halfway through. Continue stripping the layers away until the wood comes through. I found it better to let the layers dry in between stripping because it worked better. Once the wood comes through, it may be easier to finish with steel wool/sand paper.

Image

Image

Image

Step 4

Sand! We used both a circular sander (auto) and an attachment dremel sander. The dremel sander tools can be hard to find, but was so helpful to get the tiny edges. We started out with 80 grit and then finished with 220 grit. Don’t forget to wear your mask. I would also suggest using a wood filler to patch up any holes. The wood filler will not look the same as the natural wood, but will take the stain. We only did this for a small area that had termite damage.

Image

Image

Step 5

Test your stain. We hated the first stain we started with so we did 4 additional stain test pieces before we found the one we liked.

Image

You can paint the stain on with a paint brush. Let the stain sit up to 15 min and wipe it off with a cloth.

Image

Step 6

Apply wood conditioner/pre stain, especially if you have exposed rough edges where the stain can soak in more or heavy grain. This will ensure a more even staining experience.

Image

Step 7

Stain! Do this the same as your test piece. Leave on for 5-15 min and wipe off. Be careful that the stain doesn’t dry on one side if you have a big project. It can become sticky and glossy. If this happens, try using new stain over it and wiping it off. You can also sand it down as well. We did 2 coats of provincial hickory.

Image

Step 8

Finish! I suggest Tung oil for a matte/natural finish, but you can use other finishes as well. You can rub this on with a cloth, let sit overnight, and rub off any excess.

Step 9 

Admire!

(We still need to do the cabinet doors, but we need a break for now!)

Image

Image

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s