Back Unit Landscaping

Back Entrance Steps

This area looked like a jungle. It also had worn away steps so we landscaped and added new steps!

IMG_0277IMG_0278

IMG_0300

IMG_7972IMG_8710

IMG_8711IMG_0001

Back yard facing our house

Before, the unit had little privacy and over-looked our house. We added a fence to make it more private.

IMG_0299IMG_3332

IMG_0841

IMG_7178

Back unit entrance and steps

We changed these steps too and added flagstone

IMG_0295

IMG_7971IMG_7041

IMG_0837IMG_7065

Patio and Walkway

We added flagstone/landscaping overall

IMG_0297

IMG_9521IMG_8707

4IMG_0003

Other

We build/refurbished a shed for laundry

IMG_0759IMG_2358

Added gravel for parking

back pre paveIMG_7039

Back (Rental) Unit Before & After

Its been a while since I shared, but the back unit is now complete and ready to rent.

Check out the before, during, and afters!

Kitchen

IMG_7053IMG_0293

IMG_5635IMG_7184

IMG_9527IMG_9526

IMG_7060IMG_7062

IMG_7063IMG_7059

Bedroom

IMG_0284IMG_0282

IMG_0283IMG_0320

IMG_7058IMG_7049

Living Room

IMG_0292IMG_0291

IMG_0303

IMG_0291

IMG_0290

IMG_0323 IMG_0319 IMG_0318 IMG_0317

IMG_8704

IMG_0757IMG_0754

IMG_0755IMG_7051

IMG_7056IMG_7055

Bathroom

IMG_0287IMG_0285

IMG_6055IMG_0835

IMG_7334IMG_70465IMG_0834

Instructions on how to paint strip (paint stripping 101) – our other built in saga

Paint stripping isn’t the most fun task but here are some step by step instructions to make it a little easier! You need to be 100% committed but the results will be worth it in the end.

Supplies

Citristrip

Paint scraper

Sander or Manual with both 80 grit and 220 grit sand paper & steel wool (optional)

Lead paint test

Dust mask

Wood stain

Cheap paint brush

Gloves

Cloth (for rubbing in the stain & finish)

Trash bin with liner

Paper or something to cover the floor you will be stripping over

Mineral spirits to clean paint brushes if you will use a brush (optional)

Wood conditioner (optional)

Tung oil or finish (optional)

Wood filler (optional)

Patience

Pre-step

Know what you’re getting into! This will consume a lot of time, especially if the project is large. We did 2 projects at once because we wanted to finish the stripping before our new hardwoods got installed.

Image

Step 1

Get your supplies ready and prepare for the mess.

I personally liked the citristrip after I started originally with heavy duty paint stripper. The citristrip works just as well (if not better) but it is more expensive. However, after getting paint stripper accidentally on my skin and because I was doing this indoors, I went with citristrip. It smells like citrus and has a spongy texture and does not burn! It works in 30 min or less.

Image

Step 2

Check for lead paint. I wore a dust mask any way because I did some dry chipping. If you can dry chip- it saves time so try to do that first.

Image

Step 3

Put the paint stripper on until the paint bubbles and pulls away. Scrape away! Hint: the better quality scraper, the better experience you will have. We bought a $30 one halfway through. Continue stripping the layers away until the wood comes through. I found it better to let the layers dry in between stripping because it worked better. Once the wood comes through, it may be easier to finish with steel wool/sand paper.

Image

Image

Image

Step 4

Sand! We used both a circular sander (auto) and an attachment dremel sander. The dremel sander tools can be hard to find, but was so helpful to get the tiny edges. We started out with 80 grit and then finished with 220 grit. Don’t forget to wear your mask. I would also suggest using a wood filler to patch up any holes. The wood filler will not look the same as the natural wood, but will take the stain. We only did this for a small area that had termite damage.

Image

Image

Step 5

Test your stain. We hated the first stain we started with so we did 4 additional stain test pieces before we found the one we liked.

Image

You can paint the stain on with a paint brush. Let the stain sit up to 15 min and wipe it off with a cloth.

Image

Step 6

Apply wood conditioner/pre stain, especially if you have exposed rough edges where the stain can soak in more or heavy grain. This will ensure a more even staining experience.

Image

Step 7

Stain! Do this the same as your test piece. Leave on for 5-15 min and wipe off. Be careful that the stain doesn’t dry on one side if you have a big project. It can become sticky and glossy. If this happens, try using new stain over it and wiping it off. You can also sand it down as well. We did 2 coats of provincial hickory.

Image

Step 8

Finish! I suggest Tung oil for a matte/natural finish, but you can use other finishes as well. You can rub this on with a cloth, let sit overnight, and rub off any excess.

Step 9 

Admire!

(We still need to do the cabinet doors, but we need a break for now!)

Image

Image

The Fireplace and Built in Saga Nears the End

So we are almost there! We have made huge progress on the fireplace & built ins.

The worst part of the built in was getting the last amount of paint out of the grain. We still didn’t get it all, but decided to leave it for our sanity! We decided to attack our other built in too, but I will do a separate post on that one with all the supplies we used as well.

We used provincial hickory stain since that was the color of the hardwood floor we picked out. It isn’t too red, which we liked. We rubbed it with Tung oil because we didn’t want a shiny glossy finish.

Here is the before & after!

Image

Image